roof_ventilation_55
Roof - Ventillation Products

Roofline Slate Vent 600mm x 300mm

!
Optional pipe treminal can provide either 110mm or 125mm connections.

Roofline Slate Vent

Designed for easy fitting with all slate sizes, the 600mm x 300mm avoids the need for cutting upslope slates. All Corovent slate vents are supplied with a 110mm dia. Spigot for pipe termination as standard. This can be cut back to provide a full 10,000mm² ventilation.

FEATURES
Careful design ensures the slate roofline vent is virtually invisible from the ground. A box below the vent collects any water that enters it and ducts it back onto the roof

Economy Slate Vent With Pipe Adapter
!
roof_ventilation_48

Economy Slate Vent With Pipe Adapter
The COROVENT Economy Slate Vent is manufactured from long lasting injection moulded polypropylene that gives a matt slate grey finish. Use at low, mid or high level on pitches down to 200. The COROVENT HP1 pipe adaptor assembly should only be used with 600 x 300mm slates. HV1 / HP1 both provide 7, 200mm² ventilation area and include an integral 4mm insect screen. Can be cut to 500mm x 250mmwo versions give either 10mm or 25mm continuous ventilation, depending on  requirements of Building Regulations. They fit over the rafters above the wall plate and can be nailed or stapled to the rafters

HV1 600mm x 300mm

HP1 600mm x 300mm With pipe adaptor

Eaves Protection System
EPS
!
roof_ventilation1

Eaves Fascia Tray
The standard 1500mm FT150 trays are fixed above the fascia board form a lightweight rigid support for the lower edge of the underlay, which can be cut back short of the gutter.
 Formed from tough, rot-resistant rigid black thermoplastic. The FT150 is recommended for remedial and large roof areas for all slates and tiles.

Comb Filler Bird Stop
CF1
!


 

Comb Filler
1000mm. No need to buy expensive, bespoke profiled fillers. Flexible, self-adjusting fingers fill gaps left when used with profiled tiles. Prevents entry of birds and large insects.

Over Fascia Vent OV10 1m x 10mm
OV10
!

 

Over Fascia Vent 10mm
The OV10 has a unique low profile design with an overall height of 16mm, for minimum disruption to eaves detail, and allows a 10mm air gap. Matches FV10 in all other respects

Over Fascia Vent FV25 1m x 25mm
OV25
!

 

Over Fascia Vent 25mm
 The FV25 has is extremely strong, resists the weight of tiles, and crushing of foot traffic whilst roof is being finished. Ideal for use on all slate or tiled roofs.

Continuous Rafter Tray Rollout Pack
!
roof_ventilation_53
Harcon rafter trays

Continuous Rafter Tray (Rollout)
The Harcon continuous rafter tray has recently been redesigned in line with roofers’ requests. Typical roll formed rafter trays easily flatten and stretch, reducing the ventilation path. The Harcon continuous rafter tray uniquely solves this problem by incorporating structural profiling which dramatically improves rigidity, so a full 25mm air path is guaranteed down the line of the roof.
 The width of the RT66 rafter tray has been increased to 400mm, significantly wider than most roll formed rafter trays, and the RT132 rafter tray has also been introduced with a width of 800mm. These rafter trays will cover 200mm of insulation at a minimum pitch of 300 (RT66) or 150 (RT132) and will provide increased tolerance of rafter tray positioning at steeper pitches or with thinner insulation: see diagram below. Note: As the thickness of insulation increases to comply with recent regulation changes particular attention should be paid to this area of the roof.

Combination Roof Ventilation Pack
!
roof_ventilation_fp_icon
Practical, cost-effective solution for roof ventilation requirements. Pack contains 6m continuous roll of panel eaves ventilator suitable for 400, 450 and 600mm rafter centres, 6m felt support trays and 6m over fascia ventilators. 10,000mm² air flow capacity per 1m.

1 x 6m roll Corovent continuous rafter tray: RT66 or 132
10 x Corovent eaves fascia trays : FT60
6 x Corovent over fascia vents : OV10 or FV25

Single Rafter Trays
!
Available to fit three rafter spacing's. Two versions give either 10mm or 25mm continuous ventilation, depending on
requirements of Building Regulations. They fit over the rafters above the wall plate and can be nailed or stapled to the rafters.

Kits sold in 6m packs
!
 
The Corovent dry fix valley system is supplied as a complete system with all the components to fix 6m of ridge

URS6
Dry Ridge System consists of:
• 6m Dry Ridge Roll Out Tray
• 13 Dry Ridge Union Strips
• 13 Dry Ridge Caps
• 13 Dry Ridge Brackets
!

Telephone Orders

We are happy to take your order or enquiry by phone

Please call us on 0117 971 9922

We are open 8am - 6pm Monday to Friday & Saturdays 8am - 12pm

© Copyright 1994-2012, Master Plastics (SW) Ltd Bristol | Clevedon. All rights reserved world-wide.

Many of the images on this site do not belong to us. Do not copy or link directly to them. Contact us so we can seek permission where necessary on your behalf.

WE DELIVER UK NATIONWIDE ENGLAND SCOTLAND WALES AND IRELAND..